Ever Looked Inside Your Keurig? Yeah, You Need to Clean That Thing

This story is part of Home Tips, CNET’s collection of practical advice for getting the most out of your home, inside and out.

Putting your Keurig to work morning after morning will inevitably lead to some gunky buildup over time. You need to watch out — when left unchecked, mineral buildup can keep your Keurig from performing optimally. And if enough of that grime builds up to reach machine’s inner workings, the Keurig might stop running altogether.

However, it’s easy to banish gunk and keep your Keurig brewing for years to come: Just give your favorite coffee machine the TLC it deserves. The brewing system, drip trays and water tanks all require frequent attention. Even the exterior of your machine will gather unsavory stains, fingerprints and other marks of grime you’ll want to wipe away.

Here’s how to clean your Keurig and keep it in tip-top shape. (You can also learn how to make iced coffee at home, and how to organize your fridge. Plus, check out our picks for the best coffee makers, best cold-brew coffee makers and best coffee accessories.)

Wipe the outside of your Keurig brewer with a damp cloth.

Brian Bennett/CNET

1. Clean the outside of the Keurig

Start by wiping down the brewer’s exterior. Keurig actually recommends you do this daily. First, make sure the coffee maker is powered off and unplugged. Next use a damp cloth to wipe away dust and other debris from the outside of the machine. 

Pay close attention to the area on the front, right below the coffee dispenser. This section typically attracts plenty of splashes and drips.

If your Keurig brewer’s drip tray looks like this, then it’s time you clean it.

Brian Bennett/CNET

2. Wash the drip tray

Another coffee machine part that’s prone to grime is the drip tray. Liquid from spills often sits inside it unnoticed. Coffee drips can evaporate here too, leaving stains behind. A quick hand wash in the kitchen sink will clear up this mess in a jiffy. Warm water and dish soap does the trick nicely. Perform this cleaning task daily.

Clear water in a clean tray

After a quick hand wash in the sink the drip tray looks great.

Brian Bennett/CNET

3. Clean out the water tank

Here’s another daily cleaning task. That’s to give the same hand wash treatment to the water tank. Be sure to remove the water filter first if your machine has one. Depending on your brewer, your tank may be safe to throw in the dishwasher.

The pod holder was the dirtiest area on my test K-cup brewer.

Brian Bennett/CNET

4. Check the pod holder

The dirtiest section of my test Keurig K-Classic brewer was its pod holder. Grounds, dirt and dried coffee had formed a noticeable amount of crud here. To fix this, I removed the pod holder, and separated it into its two main parts. Then I gave them a water rinse and a good scrub with a damp cloth.

You may also want to use a paper clip to clear any debris from inside the brewer exit needle. The exit needle sits inside the pod holder. Take care though since that needle is sharp. Be advised that Keurig recommends you clean the pod holder every week.

A Keurig filling a mug with brownish water

Run a water-only brew cycle to flush out your Keurig coffee machine’s brewing system.

Brian Bennett/CNET

5. Flush out the whole system

Keeping your Keurig machine’s brewing system clean is critical. Dirty hardware can lead to unwanted flavors carrying over from the last brew. Tasting pumpkin spice latte in your Sumatra single origin is not ideal. Bits of grounds or other debris could cause clogs too, even a malfunction.

To clear everything out, run a daily water only brew cycle through the machine. Make sure there’s enough water in the reservoir and that the pod chamber is empty. You can run any cup size cycle you like, as long as the mug you’re brewing into is large enough to accept the liquid. 

And if you’ve never descaled your brewer, or it’s been three months since you have, consider doing so. According to Keurig, you should perform the procedure quarterly. You can use either vinegar or the company’s special descaling product. Keep in mind that it is a lengthy process requiring at least 45 minutes (4 hours with vinegar).

Still, descaling will remove any mineral deposits (often found in tap water) that may be clinging to your brewer’s internal components. This in turn ensures your coffee maker brews its optimally designed temperature. 

Once you’ve completed all these steps, wipe down the brewer again to remove any excess moisture. It should now be ready to brew in tip top shape.

For more household cleaning tips, check out how to clean a cast-iron skillethow to clean your grill and how to clean a mattress

Now playing:
Watch this:

How to clean your Keurig with distilled vinegar


More home cleaning tips and tricks 

Source link